Effect of Vanadium addition on The Structural Properties of Alloy (Ni-Cu) Nano-Particles
Article Sidebar
Main Article Content
Abstract
This research aimed to prepare (Ni-Al) alloys by powder technology method because of it is technological and commercial important. Nickel and Copper powders were tacking then there powders mixed and blended together with percent (Ni-30% Cu), Vanadium powder added to matrix alloy powder with percent (0,1,2,3)% respectively then these powders mixed to obtain homogeneous powder, then the powders compacted isostatic cold pressure at (8ton). The sintering process done at (900° C) for one hour under argon gas.
The X-ray diffractions test indicated that all alloys have Face center Cubic (F.C.C), And D alloy has best properties which include increase of phases intensity and decrease of grain size according to Debye-Scherrer equation.
The Atomic Force Microscope (AFM) also shows better properties with increase vanadium concentration. Where increased softness of surface, homogeneity surface and decrease in grain size with increase Vanadium concentration.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
Tikrit Journal of Pure Science is licensed under the Creative Commons Attribution 4.0 International License, which allows users to copy, create extracts, abstracts, and new works from the article, alter and revise the article, and make commercial use of the article (including reuse and/or resale of the article by commercial entities), provided the user gives appropriate credit (with a link to the formal publication through the relevant DOI), provides a link to the license, indicates if changes were made, and the licensor is not represented as endorsing the use made of the work. The authors hold the copyright for their published work on the Tikrit J. Pure Sci. website, while Tikrit J. Pure Sci. is responsible for appreciate citation of their work, which is released under CC-BY-4.0, enabling the unrestricted use, distribution, and reproduction of an article in any medium, provided that the original work is properly cited.
References
[1] A. Bahrami, H.R. madaah Hussein, P. Abacji, S. Miraghaei, Structural and soft electric properties of Ni-Cu alloy 85 Si 10 Ni Powders prepared by mechanical alloying, Materials Letters, Vol. 60, pp. (1068-1070), (2006) .
[2] F. Cus, Uu. Zuperl, V. Gecevska, High speed milling of light metals, Journal of Achievements in Materials and Manufacturing Engineering, Vol. 1, pp. (357-364), (2007).
[3] A. Gonzales, J. Bonastre, L. Escoda, J.J. su., Materials-Letters ,Vol. 87, pp. (1068-1070), (2003).
[4] J.R. Hayes, J.J. Gray, A.W. Szmodis, C.A. Orme, Influence of chromium and molybdenum on the corrosion of nickel-based alloy, CORROSION. The journal of science and engineering ,Vol. 62, pp. (491-500), (2006).
[5] P.L. Andresen, M.M. Morra, Stress corrosion cracking of stainless steels and nickel alloys in high-temperature water, CORROSION. The journal of science and engineering, Vol. 64, pp. (15-29), (2008).
[6] P.A. Selembo, M.D. Merrill, B.E. Logan, The use of stainless steel and nickel alloys as low-cost cathodes in microbial electrolysis cells, Journal of power sources, Vol. 190, pp. (271-278), (2009) .
[7] E. Pál, R. Kun and C. Schulze, Composition-dependent sintering behavior of chemically synthesized Cu-Ni nano particles and their application in aerosol printing for preparation of conductive microstructures, Journal Colloid Polym Science, Vol. 290, pp. (941–952), (2012).
[8] C. Kittel, Introduction to Solid State Physics,
John Wiley and sons, New York, (2005). [9] A. V. Feitosa , A new route for preparing CdS thin films by chemical bath deposition using EDTA as ligand, Brazilian Journal of Physics, Vol. 34, PP. (656-658), (2004).
[10] X. Fang, T. Zhai, U. Gautam, L. Li , L. Wu , Y. Bando and D. Golberg,, ZnS nanostructures: From synthesis to applications, Progress in Materials Science, Vol. 56 , pp. (175–287), (2011) .
[11] S. Suresh, Synthesis, structural and dielectric properties of zinc sulfide nano particles, International Journal of Physical Sciences, Vol. 8, pp. (1121-1127), (2013).
[12] A. Varea , E. Pellicer, S. Pané , B. J. Nelson, S. Suriñach, M.D. Baró and J. Sort, Mechanical Properties and Corrosion Behavior of Nano structured Cu-rich Cu Ni Electrodeposited Films, Int. Journal. Electrochemical. Science, Vol. 7, pp. (1288 – 1302), (2012) .
[13] X. Peng, X. Song and Z. Hong, Interfacial Microstructures of Fe-V-Al , Material and Design, Journal of Physics, Vol. 24, pp. (1-6), (2014) .